SB(YQP) SBDST5SH ST10SH ST16SH ST25SH ST25SH-A
1. 制動器的安裝 brake install
操縱者站在制動盤相對于制動器的對面。
Operator who stand in brake disc is opposite to brake device
1.1 擰緊手動松閘螺釘4（螺釘規格見表1）松開鎖緊的制動器并移動杠桿和摩擦襯墊，觀察和調整兩制動摩擦襯墊間的間隙。
留意：手動松閘操縱時，切勿引起電磁鐵的運動。
manually tightening screw 4 (screw specifications are seen in Table 1) loosen the locking brake and move the level and friction pad , observation and adjustment the gap between the brake and friction pad .
attention: When operate the manual loose gate , make sure not to move the electro-magnet
1.2（向上）順時針旋轉棘輪5的手輪1大約四分之一轉（微調）
(upward) clockwise rotate handwheels 1 of notch wheel 5 about 1/4 revolutions (trimming)www.yyzdq.com
1.3（向下）逆時針旋轉螺母2（用一個ф4的銷子）以便退回回推桿3，這將增加襯墊6之間的間隙，繼承該操縱，直到兩摩擦襯墊間隙超過制動盤的厚度。
(downward) anticlockwise rotate nut 2 (with a ф4 pin) in order to return the throwout lever 3, this will increase the www.7547588.comgaps between the pad 6, continues this operation, until the gap between two friction pads surpasses brake disc's thickness.
1.4將制動瓦置于其支撐物上，在制動襯墊之間插入制動盤，安裝底座連接螺栓（螺栓規格見表1）
Brake tile is placed on its strutting , www.zhidongqichang.com insert brake disc between the brake pad, installs the foundation connecting bolt (bolt specification is seen inTable 1 )
1.5檢查:
制動盤端面跳動，最大值0.2mmwww.7547555.com
A)
B) 制動盤墊塊相對于底座度： 4%
C) 制動盤相對于底座的中央距（偏差）2.5mm
留意
油漆時不要蓋住顯示棘爪運動方向的板
1.5 inspections:
A) Brake disc ending beat, maximum value 0.2mm
B) The brake disc cushion compared with the foundation: 4%
C) compared with the brake disc ,the center of the base (bias)2.5mm www.7547222.com
Attention
when paint do not cover the board that demonstrate the movement direction of pawl
2．退距的調整draws back adjustment
操縱者站在制動盤相對于制動器的對面
Operator who stand in brake disc is opposite to brake device
2.1 擰緊手動松閘螺釘4（螺釘規格見表1）松開鎖緊的制動盤，并移動杠桿和摩擦襯墊的間隙。
留意：手動松閘操縱時，切勿引起電磁鐵的運動。
manually tightening screw 4 (screw specifications are seen in Table 1) loosen the locking brake, move the pad between level and friction pad .
attention: When operate the manual loose gate , make sure not to move the electro-magnet
2.2 （向下）逆時針旋轉棘輪5的手輪1大約四分之一（微調）
(downward) clockwise rotate the handwheels 1 of notch wheel 5 about 1/4 revolutions (trimming)www.zhidong7.com
2.3 （向上）順時針旋轉螺母2（用一個ф4的銷子）直到早制動摩擦襯墊和制動盤間獲得0.5~0.7mm的總計間隙。
(upward) anticlockwise rotate nut 2 (with a ф4 pin) until the space between early friction brake and brake disc was 0.5 ~ 0.7mm
留意：在調整制動摩擦襯墊時，電磁鐵必需處于吸合狀態。（見圖3）
Attention: When adjustment brake friction liner, the electro-magnet must be in attracts gathers condition. (see in Figure 3
2.4 安裝好電磁鐵的防塵雨罩。
Installs the dustproof rain shade to electro-magnet
2.5 完全松開手動松閘螺釘4并擰緊鎖定螺母。
Loosen the bolt 4 completely and screws tight the nut.
//3、制動器的電力聯接 connect brake device
3.1 該制動器必需與ESE型經濟電源配套使用。
3.2 打開接線盒的密封蓋，用2X（ф10.5-ф15）的雙A芯電纜磁鐵的接線端子和ESE電源的十和一端子相連接，與極性無關。
3.3 ESE電源的0-220-380電源的接線端子，必需接于相應的單相電源上（電纜直徑見表）
3.1 this brake must use together with the ESE economical power source.
3.2 open the sealing gland of connecting box, with 2X (ф10.5-ф15) dual-core cables magnet ESE Terminal Blocks and power of ten and a terminal connected with nothing to do with polarity.
3.3 ESE power 0-220-380 power of the terminals must be received in the corresponding single-phase power on (see table diameter cable)with the double A core electric cable magnet's binding clamp and the ESE power source ten and a post connect, has nothing to do with the polarity. 3.3 the ESE power source's 0-220-380 power source's binding clamps, must meet on the corresponding single-phase source (electric cable diameter see table)